Skip to main content

Two people can lift the same weight and still produce force completely differently. Graphing the force a person can produce at varying velocities can visualise these differences, called a force-velocity (F-V) profile. This underpins athletic movements like jumping, sprinting and change of direction (Samozino et al., 2012).

Force and velocity trade off

A heavy squat moves slowly whereas an unweighted bar moves fast, describing the inverse relationship of force and velocity. The y-intercept is your theoretical maximum force (F0), at V = 0 (isometrics) and the x-intercept is your theoretical top speed (V0), where F = 0 (zero load).

People are individualised in their lines, with some people losing force quicker as velocity rises (strong but slow) compared to people who are fast but weaker. The gradient of your F-V profile identifies if you are force or velocity dominant in a movement (Morin and Samozino, 2016). Isolated muscles produce a curved relationship, whereas whole body movements trend towards a more linear graph (Figure 1).

Force-velocity graph of an isolated muscle showing a curved relationship
Force-velocity graph of a whole body movement showing a near-linear relationship
Figure 1. Example force-velocity graphs of both an isolated muscle and whole body movement.

Power is where force meets velocity

Power (P = F × V) is a key determinant of athletic performance (Cormie, McGuigan and Newton, 2011) which can be derived from the values along the F-V graph. The parabolic relationship of a power-velocity curve identifies the conditions at which peak power (Pmax) can be produced. A person with Pmax at lower velocities would suit slower movements, like rugby scrums, in contrast with a person who’d suit explosive movements, like sprinting. Think of it like an engine in different gears, producing the same power just at different velocities.

Parabolic power-velocity curve of a whole body movement showing peak power
Figure 2. Example power-velocity relationship of a whole body movement.

Training according to your force-velocity profile

Research shows that fixing F-V imbalances improves jump performance even when Pmax stays the same (Samozino et al., 2012). Using the F-V relationship to identify whether someone is force- or velocity-dominant allows programming to target their weaknesses (Jiménez-Reyes et al., 2017).

Someone who is more velocity dominant should be programmed heavy loads at slow to no velocity, training the muscles to produce a higher force. This can be done through heavy back squats, isometric mid-thigh pulls or weighted pull ups. These should be programmed at low reps with high rest time, maintaining quality within the reps and to allow for a full nervous system recovery between.

In contrast, a force dominant athlete’s training should look explosive. Plyometric and ballistic movements, like pogos, drop jumps or landmine punches can train speed. Banded movements can reduce bodyweight load to increase velocity, furthermore overspeed plyometrics completed on rolling carts became popular in the early 2000s as a method of reducing or completely eliminating gravitational load. These, similar to previously, should be completed with fewer, higher quality reps, with an adequate rest time in-between.

How to assess the force-velocity relationship

Force plates are the gold standard for assessing an F-V profile. Squat jumps are performed under increasing loads while the plates measure the force pushed into the ground, and velocity is calculated from that force data.

You don’t need a lab to get a useful profile though. Samozino’s simple method estimates force, velocity and power from just body mass, the load and jump height, and agrees closely with force-plate results (Samozino et al., 2008).

Isovelocity measurement devices control the velocity of a movement, and the force can be measured throughout the movement, however these are expensive and require laboratory conditions to be performed safely.

Force-velocity profiling for sprinting

At top speed, each foot during a maximal sprint is in contact with the ground for around a tenth of a second (Weyand et al., 2000) during an acceleration, so not only does an athlete need to produce a high amount of force it also needs to be produced quickly. Acceleration also requires primarily horizontal force production to propel the body forward rather than up, meaning that sprinting will have its own individual horizontal F-V profile. It can also be used to determine what percentage of your total force is produced horizontally (Morin, Edouard and Samozino, 2011).

Horizontal and vertical F-V profiles rarely match. A study comparing them across sports found them to have a low correlation, concluding a great jumper not necessarily to be a great accelerator (Jiménez-Reyes et al., 2018).

To profile horizontal F-V, a laser (such as MuscleLab) or a radar gun tracks the athlete’s velocity during a maximal sprint from a standstill. Force, velocity and power are then modelled from that speed-time data (Samozino et al., 2016).

Conclusion

Mapping the F-V relationship can tell you whether you are fast-weak or slow-strong. Training can be used to target the imbalances, improving athletic performance.

References

Cormie, P., McGuigan, M.R. and Newton, R.U. (2011) ‘Developing maximal neuromuscular power: Part 1 – biological basis of maximal power production’, Sports Medicine, 41(1), pp. 17–38.

Jiménez-Reyes, P., Samozino, P., Brughelli, M. and Morin, J.-B. (2017) ‘Effectiveness of an individualized training based on force-velocity profiling during jumping’, Frontiers in Physiology, 7, 677.

Jiménez-Reyes, P., Samozino, P., García-Ramos, A., Cuadrado-Peñafiel, V., Brughelli, M. and Morin, J.-B. (2018) ‘Relationship between vertical and horizontal force-velocity-power profiles in various sports and levels of practice’, PeerJ, 6, e5937.

Morin, J.-B., Edouard, P. and Samozino, P. (2011) ‘Technical ability of force application as a determinant factor of sprint performance’, Medicine & Science in Sports & Exercise, 43(9), pp. 1680–1688.

Morin, J.-B. and Samozino, P. (2016) ‘Interpreting power-force-velocity profiles for individualized and specific training’, International Journal of Sports Physiology and Performance, 11(2), pp. 267–272.

Samozino, P., Morin, J.-B., Hintzy, F. and Belli, A. (2008) ‘A simple method for measuring force, velocity and power output during squat jump’, Journal of Biomechanics, 41(14), pp. 2940–2945.

Samozino, P., Rejc, E., Di Prampero, P.E., Belli, A. and Morin, J.-B. (2012) ‘Optimal force–velocity profile in ballistic movements – Altius: citius or fortius?’, Medicine & Science in Sports & Exercise, 44(2), pp. 313–322.

Samozino, P., Rabita, G., Dorel, S., Slawinski, J., Peyrot, N., Saez de Villarreal, E. and Morin, J.-B. (2016) ‘A simple method for measuring power, force, velocity properties, and mechanical effectiveness in sprint running’, Scandinavian Journal of Medicine & Science in Sports, 26(6), pp. 648–658.

Weyand, P.G., Sternlight, D.B., Bellizzi, M.J. and Wright, S. (2000) ‘Faster top running speeds are achieved with greater ground forces not more rapid leg movements’, Journal of Applied Physiology, 89(5), pp. 1991–1999.